S-parameter analysis guides for every RF component type: LNA, power amplifier, bandpass filter, SAW/BAW filter, duplexer, antenna, balun, coupler, attenuator, and more.
How to analyze PA S-parameters: verify gain (S21), design output match from S22, chec...
How to analyze low-pass filter S-parameters: verify cutoff frequency, insertion loss,...
How to analyze high-pass filter S-parameters: verify cutoff frequency, passband loss,...
How to analyze BAW (Bulk Acoustic Wave) and FBAR filter S-parameters for 5G and WiFi....
How to characterize RF coaxial cables using S-parameters: measure insertion loss vs f...
How to analyze diplexer S-parameters: verify two-band filtering, port isolation, comm...
How to analyze RF switch (SPDT, SP4T) S-parameters in ON and OFF states: insertion lo...
How to analyze SMA connector S-parameters: verify return loss vs frequency, identify ...
How to characterize a bias-T (bias tee) using S-parameters: RF port insertion loss, D...
How to analyze directional coupler S-parameters: measure coupling factor (S31), main ...
How to analyze a 90-degree hybrid (branch-line coupler) S-parameters: verify 3 dB pow...
How to analyze chip antenna S-parameters on PCB: measure S11 vs frequency, identify r...
How to analyze RF SMD inductor S-parameters: extract Q factor from S21, find self-res...
How to analyze RF SMD capacitor S-parameters: compare C0G vs X7R dielectrics, measure...
How to analyze GaN HEMT S-parameters for power amplifier design: interpret low output...
How to analyze a measured or simulated matching network S-parameter file: verify S11 ...
How to analyze GaAs pHEMT transistor S-parameters: low-noise LNA design from S11/NF c...
How to analyze RF circulator and isolator S-parameters: verify forward insertion loss...
How to analyze RF limiter S-parameters: small-signal insertion loss, port match, and ...
How to analyze microstrip patch antenna S-parameters: measure S11 resonant frequency,...
How to analyze balun S-parameters: verify amplitude balance (|S21|=|S31|), phase bala...
How to analyze RF power combiners and dividers: verify equal power splitting (S21=S31...
How to analyze RF transformer S-parameters: verify impedance ratio, insertion loss, b...
How to analyze MEMS (Micro-Electro-Mechanical System) RF filter S-parameters: ultra-l...
How to analyze LTCC (Low Temperature Co-fired Ceramic) RF filter S-parameters: wideba...
How to analyze ESD protection TVS/Schottky diode S-parameters for RF lines: verify sm...
Compare wound and thin-film SMD inductor S-parameters: Q factor vs frequency, SRF, ES...
How to analyze PIN diode S-parameters in forward bias (switch ON) and reverse bias (s...
Analyze multilayer chip capacitor (MLCC) S-parameters: identify series resonance freq...
How to identify filter poles and zeros from S21 S-parameter data. Transmission zeros ...
How to analyze rat-race coupler (ring hybrid) S-parameters: verify 180° phase differe...
Learn how RF directional couplers work, key specs like coupling factor and directivit...
Understand Wilkinson power dividers, resistive splitters, isolation between output po...
Learn how RF baluns convert between balanced and unbalanced signals, key specs includ...
Understand how ferrite circulators and isolators work, their S-parameter signatures, ...
Understand RF MEMS switch operation, insertion loss, isolation, actuation voltage, an...
Technical guide to Rogers RO4003C RF substrate: dielectric constant, loss tangent, mi...
Compare RF connector types SMA, SMP, 3.5mm, 2.92mm, 2.4mm, 1.85mm by frequency range,...
Understand RF mixer operation, conversion loss, image rejection ratio, LO-RF and LO-I...
Guide to RF absorber materials including ferrite tiles, foam absorbers, carbon-loaded...
Guide to RF phase shifter types including switched-line, loaded-line, reflection, and...
Understand RF diplexer architecture, design approaches for frequency band combining/s...
S-parameter analysis, Smith chart, impedance matching, circuit simulation and SNP batch processing — all free on Android.
Download RF View Free on Google PlayAndroid 6.0+ · Free · No sign-up required